Altivar Easy 610 - ATV610U07N4

Variable speed drive ATV610 - 0.75 kW / 1HP - 380...415 V - IP20

 

Main
range of product Altivar Easy 610
product or component type Variable speed drive
product specific application Fan, pump, compressor, conveyor
device short name ATV610
variant Standard version
product destination Asynchronous motors
mounting mode Cabinet mount
EMC filter Integrated conforming to EN/IEC 61800-3 category C3 with 50 m maximum
IP degree of protection IP20
type of cooling Forced convection
supply frequency 50...60 Hz (+/-5 %)
network number of phases 3 phases
[Us] rated supply voltage 380...415 V (- 15...10 %)
motor power kW 0.75 kW normal duty
0.37 kW heavy duty

motor power hp 1 hp normal duty
0.5 hp heavy duty

line current 3.1 A at 380 V normal duty
2.9 A at 415 V normal duty
1.7 A at 380 V heavy duty
1.5 A at 415 V heavy duty

prospective line Isc 5 kA
apparent power 2.1 kVA at 415 V normal duty
1.1 kVA at 415 V heavy duty

continuous output current 2.2 A at 4 kHz normal duty
1.5 A at 4 kHz heavy duty

maximum transient current 2.4 A during 60 s normal duty
2.3 A during 60 s heavy duty

asynchronous motor control profile Constant torque standard
Variable torque standard
Optimized torque mode

output frequency 0.0001...0.5 kHz
nominal switching frequency 4 kHz
switching frequency 2...12 kHz adjustable
number of preset speeds 16 preset speeds
communication port protocol Modbus serial
option card Slot A : communication card Profibus DP V1
Slot A : digital or analog I/O extension card
Slot A : relay output card

Complementary
output voltage <= power supply voltage
motor slip compensation Adjustable
Automatic whatever the load
Can be suppressed
Not available in permanent magnet motor law

acceleration and deceleration ramps Linear adjustable separately from 0.01 to 9000 s
S, U or customized

braking to standstill By DC injection
protection type Motor : thermal protection
Motor : motor phase break
Drive : thermal protection
Drive : overheating
Drive : overcurrent between output phases and earth
Drive : overload of output voltage
Drive : short-circuit protection
Drive : motor phase break
Drive : overvoltages on the DC bus
Drive : line supply overvoltage
Drive : line supply undervoltage
Drive : line supply phase loss
Drive : overspeed
Drive : break on the control circuit

frequency resolution Display unit : 0.1 Hz
Analog input : 0.012/50 Hz

electrical connection Control, screw terminal : 0.5...1.5 mm²
Line side, screw terminal : 2.5...16 mm²
Motor, screw terminal : 2.5...16 mm²

connector type 1 RJ45 (on the remote graphic terminal) for Modbus serial
physical interface 2-wire RS 485 for Modbus serial
transmission frame RTU for Modbus serial
transmission rate 4.8, 9.6, 19.2, 38.4 kbit/s for Modbus serial
type of polarization No impedance for Modbus serial
number of addresses 1...247 for Modbus serial
method of access Slave
supply External supply for digital inputs : 24 V DC (limits : 19...30 V), <= 1.25 mA (overload and short-circuit protection)
Internal supply for reference potentiometer (1 to 10 kOhm) : 10.5 V DC +/- 5 %, <= 10 mA (overload and short-circuit protection)

local signalling 1 LED red for presence of voltage
2 LEDs for local diagnostic
1 LED yellow for embedded communication status
2 LEDs dual colour for communication module status

width 145 mm
height 297 mm
350 mm with EMC plate

depth 203 mm
product weight 2.4 kg
analogue input number 3
analogue input type Software-configurable voltage AI1, AI2, AI3 : 0...10 V DC, impedance 30 kOhm, resolution 12 bits
Software-configurable current AI1, AI2, AI3 : 0...20 mA, impedance 250 Ohm, resolution 12 bits
Software-configurable temperature probe or water level sensor AI2, AI3

discrete input number 6
discrete input type Programmable as pulse input DI5, DI6 0...30 kHz : 24 V DC (limits : <= 30 V)
Programmable as logic input DI1...DI6 : 24 V DC (limits : <= 30 V), impedance 3.5 kOhm

input compatibility Level 1 PLC conforming to EN/IEC 61131-2, logic input DI1...DI6
Level 1 PLC conforming to IEC 65A-68, pulse input DI5, DI6

discrete input logic Positive logic (source) : DI1...DI6 configurable logic input, < 5 V (state 0), > 11 V (state 1)
Negative logic (sink) : DI1...DI6 configurable logic input, > 16 V (state 0), < 10 V (state 1)
Positive logic (source) : DI5, DI6 configurable pulse input, < 0.6 V (state 0), > 2.5 V (state 1)

analogue output number 2
analogue output type Software-configurable current AQ1, AQ2 : 0...20 mA, resolution 10 bits
Software-configurable voltage AQ1, AQ2 : 0...10 V DC,impedance 470 Ohm, resolution 10 bits

sampling duration Analog input AI1, AI2, AI3 : 5 ms (+/- 0.1 ms)
Analog output AQ1, AQ2 : 10 ms (+/- 1 ms)
Discrete input DI1...DI6 : 2 ms (+/- 0.5 ms) configurable
Pulse input DI5, DI6 : 5 ms (+/- 1 ms) configurable

accuracy Analog input AI1, AI2, AI3 : +/- 0.6 % for a temperature variation 60 °C
Analog output AQ1, AQ2 : +/- 1 % for a temperature variation 60 °C

linearity error Analog input AI1, AI2, AI3 : +/- 0.15 % of maximum value
Analog output AQ1, AQ2 : +/- 0.2 %

relay output number 3
relay output type Configurable relay logic R1 : fault relay NO/NC, electrical durability 100000 cycles
Configurable relay logic R2 : sequence relay NO, electrical durability 100000 cycles
Configurable relay logic R3 : sequence relay NO, electrical durability 100000 cycles

refresh time Relay output R1, R2, R3 : 5 ms (+/- 0.5 ms)
minimum switching current Relay output R1, R2, R3 : 5 mA at 24 V DC
maximum switching current Relay output R1, R2, R3 on resistive load (cos phi = 1 : 3 A at 250 V AC
Relay output R1, R2, R3 on resistive load (cos phi = 1 : 3 A at 30 V DC
Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at 250 V AC
Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at 30 V DC

isolation Between power and control terminals
insulation resistance > 1 mOhm at 500 V DC for 1 minute to earth


Reviews For Altivar Easy 610 - ATV610U07N4

Add Your Review

Your Rating

First Name*

Last Name*

Email*

Your Review*